No the screen layout is defiantly different in the 2020 model. I have tapped until the neighbor gave me a strange look

 

Thanks for that. Unfortunately it seems quite different. I tried a couple of different combinations using various buttons instead of the tune button but nothing seemed to work. Please see attache photos.

 

Code 6998 doesn't work.
I'm the only one to find pretty difficult to trigger this menu?... it almost cost me 20 tries to open the password prompt...

 

Lots of posts here on how but none on why?

 

found this on XDA

2801 worked for me 2020 Ioniq Electric with SW 201102

 

2801 worked on my 2017 Canadian Ionic BEV with update

MODEL : AEAE.S4AMN.CA
S/W : ST.AEEV.CAN.E537.201012
FIRMWARE : MICOM.ST.AEEV.CAN.200E.201012
SUBM.ST.AEEV.1015.190416

 

I just found the "engineering mode" thread here -> https://www.ioniqforum.com/forum/290-hyundai-ioniq-user-interface/31842-ioniq-engineering-mode.html

So disregard my thread. It's a duplicate.

 

I did this yesterday on my 2 year old non plugin and it worked very well exactly like the video shows..

 

Anyone found a way to do this with the new 38kWh?

 

I assume the 38kwh infotainment system is the same as the HEV 2020 (10.25" screen)
I've not found any info regatds thos new version yet.

 

there is this method for latest fw on ioniq. Dont know if this also applies on latest Facelift ioniq. can you try and see if you can get in and let me know.

Откат c прошивки SOP.007.3.190314 автомагнитол Kia Lan6000, LAN6200, IAH8434UMNG. — KoreaCustom на DRIVE2

Блог компании KoreaCustom на DRIVE2. Для тех кто обновился на последнюю прошивку. автомагнитолы от компании LG . Lan6000 и т.д. Заходим в системная информация=>Обновить и нажимаем цифры по порядку от 1 до 6 изображённые на рисунке. Выскакивает меню с вводом пароля. Пароль вводим текущее...

www.drive2.ru

 

Try this way

 

Unfortunately my software is very different. I have AE_E_PE.AUS.5SW_L.001.001.190630
As you can see it is Australian.

 

Try the code 2400.
This is to enter dealer mode

 

Sorry to ask such a silly question but where so I enter the code?

 

 

The instructions I've seen so far are for the old Ioniq. Still haven't found anything for the 2020 38kWh.

 

hi.
i talk with hyundai today and i got this.

 

It doesn't work for me... maybe it has changed the way to access the menu after an update. The version showed in the document is sligthy older than mine.
Anyways, thanks for providing this document.

 

it`s for the 2020

 

On page 4 is for your car.
It says whit volum knob in center

 

Yeah, I've tried that procedure, adjusting the volume knob and tapping the screen on the zone the document shows, it still doesn't work
I've executed the following sequence and nothing happens: 7, tap, 3, tap, 1, tap.

 

I did it at work to day
After installing the latest software version.
Let me try again tomorrow.
I don't know how Precise you need to be.
I just pressed the screen in the lower area.

 

I did it at work to day
After installing the latest software version.
Let me try again tomorrow.
I don't know how Precise you need to be.
I just pressed the screen in the lower area.

No need, it worked... it seems that it's dependant on how fast and how precise you are when tapping the screen...
It doesn't worked for me using the volume knob at first, so I used the volume buttons from the steering wheel and it worked, then tried again with the volume knob and after some tries and fast tappings, it worked.

For those that have problems with that, try to use the volume buttons from the steering wheel instead of the volume knob, you can be more steady when tapping the screen.

Also I've been tapping this area:

Thx.

 

Bingo!!!! thank you. The second way ( page 3 and 4 ) worked for me.

 

So guys. Any of you have ioniq 2020 who tried to access the engineering menu? If yes, can you check if the menu SYSTEM is there ? And inside system look for the button auto test.

Thanx

 

Dealer mode on 2020... yes, engineering mode no. I don't know the code, putting the hh:mm as code doesn't work on this device.

Worst is that it says "Engineering mode" when inputting the password, so it must ve accessed that way. 2400 its only for dealer mode.

No autotest button found in system category on dealer mode.

 

Sorry to dig up an old post but engineering mode code for this is 0428

 

Try 2900 , 2998, 6969

 

Hello There
Does anyone successfully access those menu with the latest software version (late 2020) ??